Sundy NJ-I

Polyvinyl alcohol (PVA), an indispensable water-soluble polymer material, is used in a wide range of fields, including construction, textiles, papermaking, and chemicals. Among the many PVA specifications, mesh size, or particle fineness, is a key factor in determining processing efficiency and final product quality.   1. Mesh Size Basics: A Measurement of Particle Size Mesh size is a unit of measurement for powder particle fineness. It refers to the number of holes in a sieve per inch. The smaller the mesh size, the larger (coarser) the particles. Mesh size and dissolution rate: The dissolution process of a powder begins with the wetting and penetration of the particle surface by water molecules. The finer the particle size (the larger the mesh size), the greater its specific surface area. A larger specific surface area means that water molecules can contact more PVA molecular chains, significantly accelerating wetting, swelling, and disentanglement, ultimately increasing dissolution rate. Mesh size and dispersion uniformity: Fine particles are more easily dispersed in liquid or solid mixtures. When coarse particles (such as 20 mesh) are added to water, they are more likely to settle or clump due to density differences, forming "fish eyes" that are difficult to dissolve. Mesh Size and Dust Density: The finer the particle size, the lower the critical velocity at which it becomes suspended in air, resulting in higher dust levels. 20 mesh PVA produces low dust, while 200 mesh PVA requires strict dust control measures.   2. Introduction and Application of PVA Specifications of Different Mesh Sizes Mesh Size  20 mesh(Polyvinyl Alcohol 0588) 120 mesh (PVA 088-05S) 200 mesh (POVAL 22-88 S2) Photo Bulk Density Relatively high Medium Relatively low (fluffy powder) Key Features The largest particles have the lowest surface area. This dissolution process is the slowest, but dust generation during operation is minimal; it is also known as a "low-dust" or "dust-free" grade. This medium-sized particle size is the most commonly used grade in industry. It strikes a good balance between dissolution efficiency, ease of operation, and cost. The extremely fine particles and maximum surface area ensure the fastest dissolution and the best dispersibility. Applications Dry-mix mortar for construction: Coarse-grained PVA, as a binder, is less likely to form high-viscosity clumps during initial mixing, allowing for better dispersion in other components (such as cement and sand). It also produces minimal dust, improving the on-site construction environment.   Specialized slow-release adhesives: In certain specialized construction mortars or adhesives, PVA needs to dissolve slowly to provide lasting adhesion.   Preventing rapid thickening: Suitable for formulations that require prolonged mixing and where rapid thickening of the solution is undesirable. Conventional adhesives: Used in the manufacture of common water-based adhesives such as wood glue and paper glue.   Textile sizing agents: Prepare sizings at standard temperatures and times to meet the sizing requirements of most textiles.   Emulsion polymerization protective colloids: Serves as stabilizers and protective colloids in the polymerization of emulsions (such as VAE and acrylic emulsions). They provide a sufficiently rapid dissolution rate without excessively increasing system viscosity, ensuring stability and particle size distribution during emulsion polymerization. High-end water-based coatings: Suitable for high-end paints and putty powders that require extremely high dispersibility and a minimum of residual particles.   Fast Preparation/Low-Temperature Dissolution: Fine powder ensures rapid and thorough dissolution of PVA at low temperatures or under limited stirring capacity.   Water-Soluble Film: Used in the production of water-soluble packaging films requiring high transparency and good solubility, such as laundry bags and pesticide packaging.   Pharmaceutical/Cosmetic Excipients: Used in certain fine chemical applications requiring high precision.   3. How to Make the Best Choice? Choosing the right mesh size for PVA is essentially a trade-off between production efficiency, environmental safety, and product performance: For those seeking dissolution speed and product fineness (e.g., coatings and films): 200 mesh is preferred. For those seeking versatility, balanced performance, and moderate cost (e.g., conventional adhesives): 120 mesh is preferred(PVA 088-50S). For those emphasizing operational safety, low dust generation (e.g., large-volume batching), or specific sustained-release requirements: 20 mesh is preferred(Poval 217).   Website: www.elephchem.com Whatsapp: (+)86 13851435272 E-mail: admin@elephchem.com