PVA chemical

Polyvinyl alcohol (PVA) is widely used in the paper industry due to its excellent film-forming and adhesive properties. PVA is typically used in the paper manufacturing process as a binder, coating agent, or surface sizing agent. Here are some common applications of PVA in the paper industry:   1.Surface Sizing: PVA is used as a surface sizing agent to improve the surface properties of paper, such as its smoothness, printability, and water resistance. It forms a thin film on the surface of the paper, reducing the penetration of liquids and improving the ink receptivity.   2. Binder for Coatings: PVA is used as a binder in the formulation of coatings applied to paper surfaces. It helps in binding pigments and other additives to the paper, enhancing the color retention, gloss, and overall performance of the coatings.   3. Adhesive for Paperboard: PVA is utilized as an adhesive in the production of paperboard and cardboard boxes. It provides excellent adhesion between the layers of paper, improving the overall strength and durability of the packaging materials.   4. Release Agent: PVA can be used as a release agent in the paper industry. It is applied to the surfaces of rollers and machinery to prevent sticking and improve the smooth flow of paper during the production process.   5. Fiber Treatment: PVA can be applied to paper fibers to improve their bonding properties and enhance the paper's strength and tear resistance.   It's important to note that the specific grade of PVA used in the paper industry may vary depending on the desired properties and requirements of the paper or paperboard being produced.   Website: www.elephchem.com Whatsapp: (+)86 13851435272 E-mail: admin@elephchem.com ElephChem Holding Limited, professional market expert in Polyvinyl Alcohol(PVA) and Vinyl Acetate–ethylene Copolymer Emulsion(VAE) with strong recognition and excellent plant facilities of international standards. PVA 088-08 & 05-88   PVA 100-27 & 17-99   PVA 088-20 & 17-88  

Using succinic acid as the cross-linking agent, through the reaction of COOH- and OH-, an ester group is generated, which cross-links the PVA molecules and generates a modified PVA glue that is insoluble in water. The introduced COOH-group can improve its water resistance, hardness, adhesion, etc.   Weigh an appropriate amount of PVA, add water, heat it in a water bath with electric stirring, and control the water bath temperature to 80-90°C. After it is completely dissolved, stop heating to obtain PVA glue. In a water bath at a certain temperature, add an appropriate amount of succinic acid to the above-mentioned PVA glue, stir it under closed conditions to react, and cool to room temperature to obtain a modified PVA glue.   Using succinic acid as the cross-linking agent, PVA glue was modified, and the optimal modification conditions were determined to be: PVA glue mass concentration 7%, reaction temperature 85°C, and PVA glue to succinic acid mass ratio 5.6:1. Here Under the conditions, the hardness, adhesion, viscosity and impact resistance of the modified PVA glue obtained were significantly improved, and the water resistance was also improved. This method can be used to prepare PVA adhesives and coatings that require high adhesion and water resistance. Website: www.elephchem.com Whatsapp: (+)86 13851435272 E-mail: admin@elephchem.com ElephChem Holding Limited, professional market expert in Polyvinyl Alcohol(PVA) and Vinyl Acetate–ethylene Copolymer Emulsion(VAE) with strong recognition and excellent plant facilities of international standards.  

Polyvinyl acetal mixed aldehyde adhesive can be prepared by using polyvinyl alcohol (PVA) and crotonaldehyde as the main raw materials, hydrochloric acid (HCl) as the catalyst and acetaldehyde as the modifier.   Put a certain amount of PVA into a three-necked flask equipped with a mechanical stirrer and a reflux condensation device, add deionized water, adjust the water bath temperature to 95°C, and keep it warm for 2 hours to fully dissolve it; when the solution cools to room temperature, Slowly add measured HCl dropwise while stirring, and mix thoroughly; heat the water bath to the specified temperature, add crotonaldehyde and acetaldehyde solutions according to the formula, and stir thoroughly; after the reaction is completed, use NaOH solution to adjust the pH value to 8 to 9, and then add Add appropriate amount of urea and stir for 20 minutes.   The results show that when the reaction temperature is (90±2)℃, the reaction time is 4 h, 8% PVA solution is 200 mL, HCl is 1mL, crotonaldehyde is 1.0~1.5mL, and acetaldehyde is 4mL, acetalization The viscosity of the product is moderate, the bonding strength is relatively maximum (4.5MPa), and the water resistance is relatively good; under the premise that other conditions remain unchanged, by changing the amount of crotonaldehyde, the final viscosity of the system can be further adjusted to meet the requirements of wood. Adhesive usage requirements.   Website: www.elephchem.com Whatsapp: (+)86 13851435272 E-mail: admin@elephchem.com ElephChem Holding Limited, professional market expert in Polyvinyl Alcohol(PVA) and Vinyl Acetate–ethylene Copolymer Emulsion(VAE) with strong recognition and excellent plant facilities of international standards.   PVA 2488 & 088-50 Modified PVA 725 PVA 1788 & 088-20    

By adding nanoscale reinforcements to the composite matrix, the mechanical properties of the composite (such as strength, stiffness, elastic modulus, etc.) can be significantly improved. The polyvinyl alcohol adhesive modified with nano-silica particles is non-toxic and pollution-free. It will be widely used and is worthy of systematic research.   Current research on the modification of nanoparticles mainly focuses on the following two aspects: one is to use silica as the base, modify its surface with a modifier, and then graft the polymer; the other is to use the polymer as the base, and then graft it. branch modifier, and then graft silica. To modify nanosilica, it is generally dispersed in an organic solvent and then a modifier is added.   Introducing inorganic nanoparticles into the adhesive for modification can improve its tensile bonding strength and elongation at break. When the dosage of nanoparticles is within a certain range, the nanoparticles can be well dispersed into the adhesive matrix. Because of their huge specific surface area, they can interact strongly with the adhesive matrix, thus improving the mechanical properties of the adhesive. However, if the dosage exceeds a certain range, serious agglomeration will occur, the particle interface area will be reduced, the interaction between the nanoparticles and the adhesive matrix will also be weakened, and the content of reactive nanoparticles will be reduced, resulting in a reduction in its mechanical properties. . The mechanical property test results of the nano-modified adhesive show that when the dosage of nano-silica particles is 4%, the various performance indicators of the modified adhesive reach the maximum value.   Website: www.elephchem.com Whatsapp: (+)86 13851435272 E-mail: admin@elephchem.com ElephChem Holding Limited, professional market expert in Polyvinyl Alcohol(PVA) and Vinyl Acetate–ethylene Copolymer Emulsion(VAE) with strong recognition and excellent plant facilities of international standards.